Design A 3D Kitchen Using Adobe Photoshop

 

 

How To Design A 3D Kitchen Using Adobe Photoshop

 

Did you know that you can completely rebuild your existing kitchen layout using Photoshop on your computer?

 

You actually don’t need a professional, expensive kitchen design software. Adobe Photoshop is an excellent tool for creating just about any digital image. While Photoshop is not normally used to create 3-D artwork or designs, there are options and tools that can be used to create the effect. These techniques can be picked up with relative ease compared to using a more traditional 3-D-based design software. Once completed, your kitchen design can be used to create a full overhaul of your existing kitchen layout.

 

INSTRUCTIONS:

1. Click the line tool and set the pixel size to 4. Click the circle on the middle left section of the the screen and create a small dot (1-inch diameter or less) for the vanishing point of the illustration. This will allow you to create a 3-D kitchen using single point perspective. Draw a rectangle around the perspective point so that the dot is in the upper right corner for the back wall. Click the line tool on the upper right-hand corner and drag it to the upper right hand corner to create a ceiling line. Click on the bottom right-hand corner of the back wall rectangle and drag this to bottom right corner of the screen to create the bottom of the right wall.

kitchen layout, kitchen plan, kitchen design, kitchen layout planner, design your own kitchen layout, kitchen design software, design a 3D kitchen, 3D kitchen, Adobe Photoshop, design of kitchen, how to design a kitchen, how to design a kitchen layout

2. Click the line tool inside the dot and drag the tool diagonally to the upper right to create the top of the cupboard. Click and drag another line just under this to create the bottom front edge of the cupboard. Click on the top cupboard line halfway up the line and drag a vertical line down to connect to the bottom front edge of the cupboard. This will create the end of the cupboard.

3. Click in the bottom left corner of the cupboard and drag a horizontal line across the screen to the right to create the bottom of the cupboards. Click inside the dot and drag two lines going diagonally to the bottom right corner of the screen to create the top of the oven and kitchen counter. Click inside the dot and drag a line down and to the right so it goes off the middle bottom right of the screen. This will create the bottom of the kitchen counters and oven. Draw a rectangle with your line tool to the left of the perspective point to create the refrigerator. Click on the upper right and bottom right corner of the refrigerator and drag a line from each corner into the perspective point.

kitchen layout, kitchen plan, kitchen design, kitchen layout planner, design your own kitchen layout, kitchen design software, design a 3D kitchen, 3D kitchen, Adobe Photoshop, design of kitchen, how to design a kitchen, how to design a kitchen layout

4. Click on the line denoting the front edge of the kitchen counter, directly to the left of the back wall. Drag a line horizontally to the right until you hit the back edge of the kitchen counter. Click at the same point where the horizontal line was started and drag a vertical line down from this point to the bottom edge of the kitchen counter. This will create the back corner of the kitchen counter.

kitchen layout, kitchen plan, kitchen design, kitchen layout planner, design your own kitchen layout, kitchen design software, design a 3D kitchen, 3D kitchen, Adobe Photoshop, design of kitchen, how to design a kitchen, how to design a kitchen layout

5. Add three vertical lines inside the cupboards to create the separate cupboard doors. Click inside the dot and drag a diagonal line that is between the bottom of the cupboard and the top back of the kitchen counter. Add four vertical lines, one near the end of the counters, two grouped close together near the bottom right of the screen to create the top right section of the oven, and one in between to show the left end of the oven. Add two perpendicular horizontal lines to create the right side edge, and then two more perpendicular vertical lines to show the rest of the right side edge of the stove. Repeat this on the left end of the stove.

6. Add the handles to the refrigerator and cupboards with small rectangles that you create with vertical lines. Add the cabinets to the kitchen counter with two diagonal rectangles under the right side of the kitchen counter. Click on the square brush for the eraser and set the size to 25 pixels. Erase all the overlapping or unnecessary perspective lines you used to create the cupboards, oven, refrigerator and kitchen counter.

kitchen layout, kitchen plan, kitchen design, kitchen layout planner, design your own kitchen layout, kitchen design software, design a 3D kitchen, 3D kitchen, Adobe Photoshop, design of kitchen, how to design a kitchen, how to design a kitchen layout

7. Use the paint bucket tool to add color or shading to the picture. Click on the color you would like and dump this on the area you want colored. Create shadows by choosing a color two shades darker and dumping that on the underside or side areas of the object. Save the image as a JPEG file at maximum resolution.

kitchen layout, kitchen plan, kitchen design, kitchen layout planner, design your own kitchen layout, kitchen design software, design a 3D kitchen, 3D kitchen, Adobe Photoshop, design of kitchen, how to design a kitchen, how to design a kitchen layout

Now that you have created your dream kitchen design, you can take it to an architect or interior designer, and they will help you bring the design to life!

However, if you decide to use a kitchen design software instead, please visit our page for more information and guide on how to design your own kitchen using kitchen design software.